Home › Guides › Measuring pins
How to Measure Excavator Bucket Pins & Ear Width
Four measurements tell you exactly which pin-on bucket fits your excavator: pin diameter, ear width, pin centers and dipper width. Here is how to take each one in about five minutes, plus a size chart for the most common classes.
Have a quick coupler on your machine? You don’t need pin measurements. Buckets for couplers are sized by the coupler instead. See our quick coupler guide for Bobcat X-Change, Kubota quick attach and Wedgelock.
What you need
- Tape measure (metric is easiest)
- Calipers, if you have them
- A rag to wipe off grease
- Your phone for photos
Park on level ground, lower the bucket flat and shut the machine off before you measure. Measure in millimeters if you can: bucket pins are made in metric sizes, so a reading like 1.77" is really a 45 mm pin.
The four measurements
Pin diameter
Measure across the widest part of a bucket pin. Calipers give the best reading; a tape works too. If you can’t get to the pin, measure the inside of the hole in the bucket ear instead.
Worn pins read a millimeter or two small. Round up to the nearest standard size (35, 40, 45, 50, 65, 70, 80, 90 mm and so on).
Ear width (inside)
Measure the gap between the two bucket ears, from the inside face of one ear to the inside face of the other. Also called the hanger width or “distance between the ears.”
Measure at the bosses (the thick rings around the pin holes), where the stick and link actually sit.
Pin centers
Measure the distance between the centers of the two pins. Because the center is hard to find by eye, measure from the front edge of one pin to the front edge of the other. That gives the same number.
This is the one people get wrong most. Measure twice.
Dipper (stick) width
Measure across the end of the stick where it fits between the ears. It should be just under your ear width. The difference is taken up by shims.
A few millimeters of play is normal and is shimmed out. A big gap means a different size.
Common sizes by class
These are the pin dimensions of our pin-on buckets in each size class. Most machines in a class match, but some models differ, so measure your own before ordering.
| Class | Pin diameter | Ear width | Pin centers | Shop |
|---|---|---|---|---|
| 27CL | 35 mm | 145 mm | 200 mm | 27 class buckets |
| 35CL | 40 mm | 145 mm | 200 mm | 35 class buckets |
| 50CL | 45 mm | 170 mm | 260 mm | 50 class buckets |
| 80CL | 50 mm | 205 mm | 305 mm | 80 class buckets |
| Komatsu PC138 | 60 mm | 275 mm | 450 mm | PC138 buckets |
| 140CL | 65 mm | 260 mm | 405 mm | 140 class buckets |
| 170CL | 70 mm | 310 mm | 465 mm | 170 class buckets |
| 220CL | 80 mm | 330 mm | 455 mm | 220 class buckets |
| 300CL | 90 mm | 410 mm | 475 mm | 300 class buckets |
Rather skip the tape measure? Find your machine and we’ll show only the buckets that fit it.
Common questions
Do the pins come with the bucket?
Our pin-on buckets ship ready to mount for your machine’s pin size. If you’re unsure what’s included for a specific bucket, check the product page or call us.
My measurement is between two sizes. Which do I pick?
Pins wear smaller and holes wear bigger, so round to the nearest standard size. If you’re still between two, send us photos of your tape on the pin and ears and we’ll confirm.
Are excavator buckets universal?
No. Two machines of the same weight can use different pins or ear widths. Matching all four measurements, or picking your exact machine on our machines page, is the reliable way to get a fit.
What if it doesn’t fit?
Buckets ordered for a listed machine are covered by our Machine-Fit Guarantee.